Item Number:DS200DCFBG2BNC
Brand: GE
Price: $5000
Lead Time: In stock
Condition: New
Payment: T/T
Shipping Port: Fujian,China
Send Inquiry
Description
Technical Parameters
Product Introduction
The DS200DCFBG2BNC board contains a gate array circuit that controls the firing of the SCRs in the bridge based upon control signals received from the SDCC/LDCC board through connector 1PL. The gate array is programmed at power-up by a serial PROM.Compatible with DC2000, AC2000, CB2000, ME2000 and FC2000 series drive devices.
Technical Specifications
Manufacture
General Electric(GE)
Model
DS200DCFBG2B
Part Number
DS200DCFBG2BNC
Description
POWER SUPPLY BOARD
Series
Mark V Speedtronic
Origin
USA
Dimension
32*24*5cm
Weight
0.75kg
Product Details
The DS200DCFBG2BNC board includes a motor voltage attenuation circuit that provides an analog representation of the motor voltage. This signal is sent to the SDCC/LDCC board through 1PL-6. The attenuation circuit is biased at 2.5 V, and can vary from 0 to 5 V depending on the motor voltage. DIP switch SW6 is used to scale the motor voltage feedback.
The DCFB board contains amplifier circuits that process the AC line-to-line voltages. The voltage feedback signals are sent to the SDCC/LDCC board through 1PL-11, 1PL-12, and 1PL-29. These signals are used to detect power bridge SCR failures and may also be used to derive the synchronization signal for the firing of the SCRs. DIP switches SW1, SW2, and SW3 are used to scale the AC line voltage feedback.
Sample Board Part Number, DS Series:
DS
Identifies GE Industrial Control Systems.
-200
Indicates that the board does not contain firmware. (215 indicates the board contains firmware and/or other components added to the base level board.)
-DCFB
Board functional acronym.
-G
A group, or variation, of a particular board.
-A
A board revision (functional change) that is not backward compatible.Essentially, a new catalog number.
-A
A board revision (functional change) that is backward compatible.
-A
A board revision (artwork change) that is backward compatible.
EE PARAMETER ADJUSTMENT
After installing a new DS200DCFBG2BNC board, the EE parameter for voltage feedback offset, EE.574 (VFBOFS), must be adjusted. The procedure for performing this adjustment varies with the application of the board and the tools that are available (programmer board, ST2000, GE Control System Toolbox, or LynxOS Configurator).
The DS200DCFBG2BNC board is used in DC2000, CB2000, EX2000,FC2000, GF2000, ME2000, and AC2000 IGBT drive applications. Refer to the applicable drive instruction book for performing the EE parameter adjustment procedure, if applicable.
This equipment contains a potential hazard of electric shock or burn. Only adequately trained persons who are thoroughly familiar with the equipment and the instructions should install or maintain this equipment.
BOARD IDENTIFICATION
A printed wiring board is identified by an alphanumeric part (catalog) number stamped on its edge. For example, the Power Supply Board is identified by part number DS200DCFBG#ruu.
WARRANTY TERMS
We offer in-stock products with a one-year warranty and fast global shipping with prompt response.
FAQ
Q: What is the input voltage range for DS200DCFBG2BNC?
A: The communication input voltage range of this module is typically 38V to 115V AC.
Q: Does this module have diagnostic functionality?
A: This module is equipped with:
Two LED indicators
One neon light status indicator
Q: Does the DS200DCFBG2BNC have a protection mechanism?
A: The module is equipped with 3 protective fuses to prevent damage to the equipment caused by overcurrent or power surges.
Q: What is the installation method for DS200DCFBG2BNC?
A: This module is usually installed in the internal slots of the drive cabinet or the excitation control cabinet.
Hot Tags: DS200DCFBG2BNC,GE DS200DCFBG2B,MRP433745,Mark V DS200DCFBG2B,DC feedback power board,GE Speedtronic Mark V DS200
